Disco Parts

[tomaco1]

If anyone needs parts off a 97 Disco SE let me know. I'm taking one apart because I need just the Axles.

[Bozman]

PM sent.

[TDI Guy]

what rims are on it?

[rover26c]

Don't want to hi-jack this thread, but i have a spare steel wheel w/ tire from a 99 D1.

[tomaco1]

Deep dish, not the boosts unfortunately

[evilfij]

I need one of the little black caps that covers the nut that holds the wiper arm on. I would take both. RN says they are NLA. :(

[dave_lucas]

Tom,

I like the deep dish rims, do you think you could get them shipped to Colorado for a decent price?

[tomaco1]

I'll check on the wiper nut thing tomorrow, and the wheels would probably be about $15 -20 a piece to ship.

Follow-up Post:

I'll check on the parking brake also.

[dave_lucas]

Will send you a PM about the rims Tom

[isleofbones]

Tom-
I still need the front crossmember. If I can come over and cut it off, that would be great.
Also, it would give you a chance to see my d-90 since the restoration and I'd like to see your progress. Just tell me how much you want for the crossmember.
Mike

[tomaco1]

Got both of these if you want them.I need one of the little black caps that covers the nut that holds the wiper arm on. I would take both. RN says they are NLA. :(

Follow-up Post:

Might be a week or two, but its yours,Tom-
I still need the front crossmember. If I can come over and cut it off, that would be great.
Also, it would give you a chance to see my d-90 since the restoration and I'd like to see your progress. Just tell me how much you want for the crossmember.
Mike

[AmityD90]

Tom
what engine does it have? My brother in law I believe has a 4.0 on his 96 Disco and could probably use some engine parts. I've been bugging him to fix her up so he can go wheeling. It's a nice 5 speed that needs just a little engine work and it will be good to go. Let me know. He's in Blue Point and it would be easy for both of you.

Gery

[isleofbones]

Tom-
Thanks... Just let me know when I can get it and I'll come by.
Mike

[tomaco1]

Mike- let me know how far back you need it
Ron- I have the wiper thingys
Nashville rover-im using the axels from the disco on my truck, but I will jhave the the 1985 rear drum axel low miles
Working on the ebrake
Amity- let me know what he wants

[NashvilleRover]

I am putting 24 spline RoverTracks in my 89 and Revor informs me that I need the two rear stub axles and hubs from a 94 or later Range Rover Classic or Disco. That is why and what I am looking for.
Let me know.
Thanks
D

[AmityD90]

Tom
I sent you a pm

[isleofbones]

Tom-
I could use the front crossmember attached to the side rails and it would be great if I could have the side rails cut about 5"-6" behind the back edge of the crossmember. If you are cutting it, that's great. If you need me to come by and cut it, that's fine too. Just let me know.
Thanks Again,
Mike

[jvelador]

Are any of the Deep Dish alloys still available? Just got a killer deal from RoverDude on 4. I need one, maybe two, depending on price.

That RoverDude sure is a generous fellow :)

[Abrooks]

Are the seat switches intact and working?

[tomaco1]

I can check the seat switches in the AM. The wheels I'd rather keep as a set, shipping to west coast would cost you anyway.

[EWR]

front and rear wiper arms? I don't need the little black caps..

[tomaco1]

If you guys need doors, seats, etc, you can just come pick them up! just buy some pizza for the kids that took the truck apart.